- AeroCopilot
- /
- Diretivas de Aeronavegabilidade
- /
- FAA-2025-10332
FAA-2025-10332
Airworthiness Directives; Pratt & Whitney Division Engines
Resumo Rápido
- Número AD
- FAA-2025-10332
- Autoridade
- FAA
- Data de emissão
- 06/06/2025
- Data efetiva
- —
- Criticidade
- routine
Autoridade
Federal Aviation Administration (EUA)
Data de Publicação
06 de junho de 2025
Data Efetiva
Não informada
Prazo de Cumprimento
Antes do próximo voo
Resumo da Diretiva
A FAA propõe adotar uma nova diretiva de aeronavegabilidade (AD) para certos motores Pratt & Whitney Division (PW) Modelos PW4074, PW4074D, PW4077, PW4077D, PW4084D, PW4090 e PW4090-3. Esta AD proposta foi motivada por uma análise de um evento envolvendo um motor International Aero Engines, LLC (IAE LLC) Modelo PW1127GA-JM, que experimentou uma separação do rotor com pás integrais (IBR-7) do estágio 7 do compressor de alta pressão (HPC), resultando em uma decolagem abortada. Esta AD proposta exigiria inspeções ultrassônicas de varredura angular (AUSIs) repetitivas dos discos do estágio 15 do HPC, cubos da turbina dianteira, selos de ar do estágio 1 da turbina de alta pressão (HPT) e cubos do estágio 2 da HPT para indicações de trincas, e remoção de serviço e substituição se necessário, e para certos números de série, remoção de serviço e substituição do selo de ar do estágio 1 da HPT. A FAA propõe esta AD para abordar a condição insegura nestes produtos.
The FAA proposes to adopt a new airworthiness directive (AD) for certain Pratt & Whitney Division (PW) Model PW4074, PW4074D, PW4077, PW4077D, PW4084D, PW4090, and PW4090-3 engines. This proposed AD was prompted by an analysis of an event involving an International Aero Engines, LLC (IAE LLC) Model PW1127GA-JM engine, which experienced a high-pressure compressor (HPC) 7th-stage integrally bladed rotor (IBR-7) separation that resulted in an aborted takeoff. This proposed AD would require repetitive angle ultrasonic scan inspections (AUSIs) of the HPC 15th-stage disks, front turbine hubs, high pressure turbine (HPT) 1st-stage air seals, and HPT 2nd-stage hubs for crack indications, and removal from service and replacement if necessary, and for certain serial numbers, removal from service and replacement of the HPT 1st-stage air seal. The FAA is proposing this AD to address the unsafe condition on these products.Texto Completo da Diretiva
Expandir texto completo (Federal Register)Texto completo (Federal Register)
Document Headings Document headings vary by document type but may contain the following: • the agency or agencies that issued and signed a document • the number of the CFR title and the number of each part the document amends, proposes to amend, or is directly related to • the agency docket number / agency internal file number • the RIN which identifies each regulatory action listed in the Unified Agenda of Federal Regulatory and Deregulatory Actions See the Document Drafting Handbook for more details. Department of Transportation Federal Aviation Administration • 14 CFR Part 39 • [Docket No. FAA-2025-0923; Project Identifier AD-2024-00529-E] • RIN 2120-AA64 AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Notice of proposed rulemaking (NPRM). SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD) for certain Pratt & Whitney Division (PW) Model PW4074, PW4074D, PW4077, PW4077D, PW4084D, PW4090, and PW4090-3 engines. This proposed AD was prompted by an analysis of an event involving an International Aero Engines, LLC (IAE LLC) Model PW1127GA-JM engine, which experienced a high-pressure compressor (HPC) 7th-stage integrally bladed rotor (IBR-7) separation that resulted in an aborted takeoff. This proposed AD would require repetitive angle ultrasonic scan inspections (AUSIs) of the HPC 15th-stage disks, front turbine hubs, high pressure turbine (HPT) 1st-stage air seals, and HPT 2nd-stage hubs for crack indications, and removal from service and replacement if necessary, and for certain serial numbers, removal from service and replacement of the HPT 1st-stage air seal. The FAA is proposing this AD to address the unsafe condition on these products. DATES: The FAA must receive comments on this proposed AD by July 21, 2025. ADDRESSES: You may send comments, using the procedures found in 14 CFR 11.43 and 11.45, by any of the following methods: • Federal eRulemaking Portal: Go to regulations.gov. Follow the instructions for submitting comments. • Fax: (202) 493-2251. • Mail: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE, Washington, DC 20590. • Hand Delivery: Deliver to Mail address above between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. AD Docket: You may examine the AD docket at regulations.gov under Docket No. FAA-2025-0923; or in person at Docket Operations between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this NPRM, any comments received, and other information. The street address for Docket Operations is listed above. Material Incorporated by Reference: • For PW material identified in this proposed AD, contact PW, 400 Main Street, East Hartford, CT 06118; phone: (800) 565-0140; email:help24@prattwhitney.com; website: connect.prattwhitney.com. • You may view this material at the FAA, Airworthiness Products Section, Operational Safety Branch, 1200 District Avenue, Burlington, MA 01803. For information on the availability of this material at the FAA, call (817) 222-5110. FOR FURTHER INFORMATION CONTACT: Molly Sturgis, Aviation Safety Engineer, FAA, 2200 South 216th Street, Des Moines, WA 98198; phone: (562) 627-5373; email: molly.a.sturgis@faa.gov. SUPPLEMENTARY INFORMATION: Comments Invited The FAA invites you to send…
Fonte: Federal Register (federalregister.gov). Texto original em inglês. Conteúdo sanitizado por segurança.
Documentos e Referências
Monitore DAs automaticamente para sua aeronave
Cadastre sua aeronave no AeroCopilot e receba alertas por e-mail e notificação quando novas diretivas de aeronavegabilidade afetarem seu tipo de aeronave.
Dados obtidos do Federal Register (federalregister.gov). As informações são fornecidas para fins de consulta — consulte sempre a fonte oficial para fins de compliance regulatório.