2025-11340

Document Headings Document headings vary by document type but may contain the following: • the agency or agencies that issued and signed a document • the number of the CFR title and the number of each part the document amends, proposes to amend, or is directly related to • the agency docket number / agency internal file number • the RIN which identifies each regulatory action listed in the Unified Agenda of Federal Regulatory and Deregulatory Actions See the Document Drafting Handbook for more details. Department of Transportation Federal Aviation Administration • 14 CFR Part 39 • [Docket No. FAA-2024-2668; Project Identifier AD-2024-00561-E; Amendment 39-23061; AD 2025-12-03] • RIN 2120-AA64 AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Final rule. SUMMARY: The FAA is superseding Airworthiness Directive (AD) 2023-09-06, which applied to all CFM International, S.A. Model (CFM) LEAP-1A23, LEAP-1A24, LEAP-1A24E1, LEAP-1A26, LEAP-1A26CJ, LEAP-1A26E1, LEAP-1A29, LEAP-1A29CJ, LEAP-1A30, LEAP-1A32, LEAP-1A33, LEAP-1A33B2, and LEAP-1A35A (LEAP-1A) engines. AD 2023-09-06 required replacement of certain high-pressure turbine (HPT) rotor stage 1 disks (HPT stage 1 disks), forward outer seals, and compressor rotor stages 6-10 spools. AD 2023-09-06 also prohibited installation of an HPT stage 1 disk, forward outer seal, or compressor rotor stages 6-10 spool that has a part number and serial number identified in the service information onto any engine. Since the FAA issued AD 2023-09-06, the manufacturer identified additional affected parts that were manufactured from material suspected to have reduced material properties due to iron inclusion, which prompted this AD. This AD retains the requirements to replace certain HPT stage 1 disks, forward outer seals, and compressor rotor stages 6-10 spools and expands the applicability to include additional affected parts manufactured from the same material suspected to have reduced material properties due to iron inclusion. The FAA is issuing this AD to address the unsafe condition on these products. DATES: This AD is effective July 25, 2025. The Director of the Federal Register approved the incorporation by reference of a certain publication listed in this AD as of July 25, 2025. The Director of the Federal Register approved the incorporation by reference of certain other publications listed in this AD as of June 23, 2023 (88 FR 32092, May 19, 2023). ADDRESSES: AD Docket: You may examine the AD docket at regulations.gov under Docket ( printed page 26196) No. FAA-2024-2668; or in person at Docket Operations between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this final rule, any comments received, and other information. The address for Docket Operations is U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE, Washington, DC 20590. Material Incorporated by Reference: • For CFM material identified in AD, contact CFM, GE Aviation Fleet Support, 1 Neumann Way, M/D Room 285, Cincinnati, OH 45215; phone: (877) 432-3272; email:aviation.fleetsupport@ge.com. • You may view this material at the FAA, Airworthiness Products Section, Operational Safety Branch, 1200 District Avenue, Burlington, MA 01803. For information on the availability of this material at the FAA, call (817) 222-5110. It is also available atregulations.gov under Docket No. FAA-2024-2668. FOR FURTHER INFORMATION CONTACT: Mehdi Lamnyi, Aviation Safety Engineer, FAA, 2200 South 216th Street, Des Moines, WA 98198; phone: (781) 238-7743; email: mehdi.lamnyi@faa.gov. SUPPLEMENTARY INFORMATION: …

Fonte: Federal Register (federalregister.gov). Texto original em inglês. Conteúdo sanitizado por segurança.