2022-19902

Document Headings Document headings vary by document type but may contain the following: • the agency or agencies that issued and signed a document • the number of the CFR title and the number of each part the document amends, proposes to amend, or is directly related to • the agency docket number / agency internal file number • the RIN which identifies each regulatory action listed in the Unified Agenda of Federal Regulatory and Deregulatory Actions See the Document Drafting Handbook for more details. Department of Transportation Federal Aviation Administration • 14 CFR Part 39 • [Docket No. FAA-2021-1168; Project Identifier AD-2021-00825-T; Amendment 39-22138; AD 2022-16-09] • RIN 2120-AA64 AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Final rule. SUMMARY: The FAA is adopting a new airworthiness directive (AD) for certain The Boeing Company Model 737-8 airplanes. This AD was prompted by a report that, during production, a small number of fasteners in certain locations of the center fuel tank were cap sealed on top of a black stripe of ink with a clear overcoat. This clear overcoat is not an approved surface for sealing and can potentially compromise sealant adhesion. Compromised sealant adhesion can, over time, affect the lightning-protection properties of the airplane. This AD requires preparation of the affected surface areas to ensure that there is adequate sealant adhesion, and complete encapsulation of the discrepant fastener locations with the approved production sealant. The FAA is issuing this AD to address the unsafe condition on these products. DATES: This AD is effective October 20, 2022. The Director of the Federal Register approved the incorporation by reference of a certain publication listed in this AD as of October 20, 2022. ADDRESSES: For service information identified in this final rule, contact Boeing Commercial Airplanes, Attention: Contractual & Data Services (C&DS), 2600 Westminster Blvd., MC 110-SK57, Seal Beach, CA 90740-5600; telephone 562-797-1717; internet www.myboeingfleet.com. You may view this service information at the FAA, Airworthiness Products Section, Operational Safety Branch, 2200 South 216th St., Des Moines, WA. For information on the availability of this material at the FAA, call 206-231-3195. It is also available at www.regulations.gov by searching for and locating Docket No. FAA-2021-1168. Examining the AD Docket You may examine the AD docket at www.regulations.gov by searching for and locating Docket No. FAA-2021-1168; or in person at Docket Operations between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this final rule, any comments received, and other information. The address for Docket Operations is U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE, Washington, DC 20590. FOR FURTHER INFORMATION CONTACT: Chris Baker, Aerospace Engineer, Propulsion Section, FAA, Seattle ACO Branch, 2200 South 216th St., Des Moines, WA 98198; phone and fax: 206-231-3552; email: christopher.r.baker@faa.gov. SUPPLEMENTARY INFORMATION: Background The FAA issued a notice of proposed rulemaking (NPRM) to amend 14 CFR part 39 by adding an AD that would apply to certain The Boeing Company Model 737-8 airplanes. The NPRM published in the Federal Register on February 23, 2022 (87 FR 10110). The NPRM was prompted by a report that, during production, a small number of fasteners common to upper wing panel stringers U-S1, U-S10, U-S12, U-S20, and U-S21 and lower wing panel stringer L-S14 were cap sealed on top of a black stripe of ink with a clear overcoat. The black stripe of ink and clear overcoat were applied during airplane assembly to cer…

Fonte: Federal Register (federalregister.gov). Texto original em inglês. Conteúdo sanitizado por segurança.